ADC 6014 User Manual download pdf

Model 6013/6014

4-3 6015 JUNCTION BOX

The 6084 Junction Box is for terminating

thermocouples and other inputs.

The interior of the thermocouple junction box must be

at a uniform temperature to minimize temperature

differential between the thermocouple connections

and the temperature sensor. Therefore, it is important

that the cover be installed after connections are made

and that the grommet through which the cables enter

be sealed. It is also recommended that the junction

box be placed in a location that has the lowest

temperature variation. If temperature variations are

extreme, the junction box may be filled with Styrofoam

or similar insulating material to reduce air movement.

The layout of the terminal blocks in the junction box is

shown in the following diagram along with the terminal

signal assignments. Notice that channel 0 is

assigned to junction terminal block 1 in the lower left.

6084 Junction Box

The 6015 junction box has isothermal screw

terminals and a sensor that measures the

temperature of the terminations. Knowing the

temperature, PI660 software will remove the

temperature error introduced by connecting the

thermocouple wire to the copper measurement

circuit. The 6084 also has a circuit that causes

the measurement to exceed full scale if an input

opens and has a location for the user to install a

low-pass filter. The 6084 comes standard with 3

meters of cable for connecting to the 6013. Longer

cable length may be special ordered for remotely

locating thermocouple terminations. 1 meter of the

cable is used to up from routing through the cable

egress of the 6000 enclosure leaving 2 meters

useable outside enclosure.

6015

1 Thermocouple Input Circuit

1 2 3 4 5 6 ... 10 11

Summary of Contents

Page 1

Model 6013/6014 4-3 6015 JUNCTION BOX The 6084 Junction Box is for terminatingthermocouples and oth

Page 2

Model 6013/6014 LED and LED Off turn on and off the LED on the front of the channel card. This featur

Page 3 - 50-Pin Type D

Model 6013/6014 4-7.4 Filter The standard anti aliasing filter is a four-pole, Butterworth low pass with plug-in frequencyselec

Page 4 - 6013 Typical Inputs

Model 6013/6014 4-4 6081 SCREW TERMINAL ADAPTER The 6081 Screw Terminal Adapter is for makingconnecti

Page 5

Model 6013/6014 012301230123012301230123GuardGuardGuardGuard-In-In-In-In+In+In+In+In-Exc-Exc-Exc-Exc

Page 6

Model 6013/6014 +In-InGuardThermocouple+In-In+Exc-ExcEcomGuard+12/15-12/15ComDC LVDTOutOut+In-InGuardV

Page 7

Model 6013/6014 Guard+In-In+DC-DCDiffAmpGainCal(DAC)Filter+1MonitorMuxADCFIFOFIFOCh 1Ch 7AutoZero(DA

Page 8

Model 6013/6014 +In-InGuardIES or ICP TransducerAC Coupled+In-InGuardVoltage SignalAC or DC CoupledIES

Page 9

Model 6013/6014 Guard+In-In+DC-DCDiffAmpGainCal(DAC)Filter+1MonitorMuxADCFIFOFIFOCh 1Ch 7AutoZero(DA

Page 10

Model 6013/6014 +In-InGuardIES or ICP TransducerAC Coupled+In-InGuardVoltage SignalAC or DC CoupledIES

Page 11

Model 6013/6014 4-6.6 DC-Powered Transducers Like the 6013, the 6014 can supply DC power for operati

Comments to this Manuals

No comments

ADC 6014 User Manual

Browse online or download User Manual for Noise Reduction Machine ADC 6014. Model 6013/6014 6084 Junction Box 6015-1

Summary of Contents

Comments to this Manuals